Bathroom Vanity Sizes: Single, Double and Hotel Formats Compared
Bathroom vanity sizes are driven by basin count, wall run and door swing, not by a catalogue. Single vanities suit runs under 1,200mm, doubles need 1,500mm or more, and hotel formats are set by the guest room drawing. Production runs 25-35 days after drawing approval.
Bathroom vanity sizes follow basin count and wall run: a single vanity needs roughly 600-1,200mm of wall, a double needs 1,500mm or more, and hotel formats are set by the guest room drawing rather than a standard. Production runs 25-35 days after drawing approval and deposit, so size decisions must be locked before that clock starts.
What are the standard bathroom vanity sizes for single and double basins?
There is no universal standard, but the market bands are consistent enough to plan around. A single-basin vanity is normally specified between 600mm and 1,200mm wide. A double-basin vanity starts around 1,500mm and runs to 1,800mm or beyond. The number that actually governs the design is the clear wall run left after the door swing, the shower screen and any side clearance.
Two rules of thumb that hold up on site:
- Allow a minimum of about 600mm of clear wall per basin, plus the gap between them.
- Leave at least 150-200mm of clear counter each side of a basin so a user has somewhere to put things down.
Below 600mm you are into a powder-room or cloakroom unit, which is a different product with a smaller basin and often a shallower carcass. Above 1,800mm on a double, the counter usually needs a mid support or a leg frame, because a long span with two basins full of water is a load case, not a drawing detail.
How do hotel bathroom vanity sizes differ from residential ones?
Hotel vanities are not sized from a standard table. They are sized from the guest room drawing, and the constraint is usually the bathroom door swing and the shower or bath position, not the vanity itself. A typical hotel single vanity sits in the 900-1,200mm band with a counter that runs wall to wall, and the carcass is often shallower than a residential unit to keep the circulation clear.
Three things change in hotel work compared with a house:
- Repeatability. One approved drawing is produced many times. Any error is multiplied by the room count, so the drawing approval stage matters more than the unit price.
- Fixed services. Plumbing and drainage positions are set by the MEP drawing before the vanity is made. The basin cut-out is CNC'd from the basin template, not from a dimension on a sketch.
- Wet-area detailing. Specify a moisture-resistant core, state the substrate in the drawing, seal all cut edges, and detail the back panel clearance so the unit is not flat against a damp wall.
Most failures in wet-area vanities come from substrate and sealing, not the finish. That is a specification decision, and it is yours to make in writing.
How much wall run and floor space does each format need?
The table below compares the three formats on the numbers that drive cost and layout. Widths are market planning bands, not a published product range — confirm the final dimension on your own drawing.
| Format | Typical width band | Basins | Where it fits | Main cost driver |
|---|---|---|---|---|
| Cloakroom / powder room | Under 600mm | 1 small | WC or secondary bath | Small basin, shallow carcass |
| Single residential | 600-1,200mm | 1 | Family bathroom, ensuite | Door finish and countertop |
| Double residential | 1,500-1,800mm+ | 2 | Master ensuite, shared bath | Countertop length, mid support |
| Hotel guest room | 900-1,200mm, wall to wall | 1 | Standard guest bathroom | Repeatability, wet-area substrate |
| Hotel suite / accessible | 1,500mm+ | 1-2 | Suite, accessible room | Clearance compliance, hardware |
Accessible rooms are the format buyers most often get wrong. The clearance requirement is set by local code, not by the factory, so it must come from your consultant before the drawing is issued.
What drives the price difference between a single and a double vanity?
The carcass is not the swing factor. In quoting experience the three biggest price swings on any vanity run are the door finish, the countertop and the hardware brand, in that order. A PVC membrane door and a high-gloss lacquer door can be the same panel underneath and differ heavily in price.
Going from single to double adds cost in four places:
- Countertop length. Quartz, sintered stone, solid surface or granite are priced by area and by cut-outs. Two basin cut-outs cost more than one.
- Second basin and tap set. Usually client-supplied, but it belongs in the budget.
- Structure. A longer span needs a mid support or leg frame.
- Freight volume. A double vanity occupies more cubic metres, and freight is charged on volume, not on unit count.
On carcass board, an E0 plywood carcass typically costs 25-40% more than a melamine-faced particleboard carcass on the same run. The gap buys moisture resistance and screw-holding strength — which matters more in a bathroom than in a kitchen, because the unit sits in a wet area.
How do vanity sizes affect shipping cost and lead time?
Freight is charged on volume, so vanity size is a logistics decision as much as a design one. Flat-pack reduces the volume you pay freight on; assembled shipping is a decision with its own cost, not a default. For a single house, assembled is often the simpler buy. For a multi-unit project with a trained crew, flat-pack is where the freight saving is real.
Timing numbers that hold across markets:
- Production: 25-35 days after drawing approval and deposit. The clock starts at approved drawings, not at enquiry.
- Door to door: usually 5-8 weeks once booking, sailing, clearance and haulage are added.
- Full door-to-door planning window: roughly 9-14 weeks depending on destination.
- Ocean freight on a single trial set: USD 1,200-3,500, plus destination charges.
MOQ starts at 1 set for sampling, with project pricing from 20 sets upward. On a single set, freight, duty and fixed charges dominate the landed cost — so a trial vanity is a specification test, not a cheap project order.
What should a buyer demand in writing before approving a vanity drawing?
Ask for the substrate by name, the door finish by process, the hardware brand and model, and the countertop material. Ask for the basin template source, the back panel clearance, and confirmation that all cut edges are sealed. Ask what the lead time is measured from — the answer should be drawing approval plus deposit.
Do not accept a thickness, a board grade or a hardware rating that is not written on the approved drawing. Those are the numbers that decide whether the unit survives a wet room for a decade, and they are the numbers a factory should be willing to commit to on paper before production starts.
Frequently asked questions
What is the standard width of a single bathroom vanity?
Single-basin vanities are normally specified between 600mm and 1,200mm wide. Below 600mm you are into cloakroom or powder-room territory with a smaller basin. The real constraint is the clear wall run left after the door swing and shower screen, so measure that first and size the vanity to it.
How wide does a double vanity need to be?
Double-basin vanities start around 1,500mm and commonly run to 1,800mm or more. Allow roughly 600mm of clear wall per basin plus the gap between them, and 150-200mm of counter each side. Above 1,800mm the counter usually needs a mid support or leg frame.
Are hotel bathroom vanities a standard size?
No. Hotel vanities are sized from the guest room drawing, where the bathroom door swing and shower position usually set the limit. A typical hotel single vanity sits in the 900-1,200mm band with a wall-to-wall counter and a shallower carcass than a residential unit. Repeatability matters more than unit price.
How long does it take to manufacture a custom vanity?
Production runs 25-35 days after drawing approval and deposit. Door to door is usually 5-8 weeks once booking, sailing, clearance and haulage are added, and roughly 9-14 weeks for longer lanes. The clock starts at approved drawings, not at enquiry, so drawing sign-off is the schedule risk.
What is the minimum order for custom vanities?
MOQ starts at 1 set for sampling, with project pricing from 20 sets upward. On a single set, ocean freight of USD 1,200-3,500 plus destination charges dominate the landed cost, so a trial order is best treated as a specification test rather than a cheap project order.
Does a double vanity cost much more than a single?
The carcass is not the swing factor. Cost rises through countertop length, a second basin and tap set, a mid support for the longer span, and more freight volume. The three biggest price swings on any vanity run are the door finish, the countertop and the hardware brand, in that order.
Should I ship vanities flat-pack or assembled?
Freight is charged on volume, so flat-pack reduces what you pay. But it depends on your installation crew. If assembly quality on site is uncertain, the freight saving can be spent twice fixing joints. For a single house, assembled is often simpler; for a multi-unit project with a trained crew, flat-pack is where the saving is real.
What should be written on an approved vanity drawing?
The substrate by name, the door finish by process, the hardware brand and model, the countertop material, the basin template source, the back panel clearance, and confirmation that all cut edges are sealed. Do not accept a thickness, board grade or hardware rating that is not stated on the approved drawing.