Custom vs Ready-Made Cabinets Philippines: Which Is Cheaper?

ONE HOME BUILD

Ready-made cabinets win on the first invoice; custom cabinets usually win on the 5-10 year total. The gap is set by carcass board, door finish, hardware brand and freight — not by floor area. Here is how to compare both numbers on the same specification.

Ready-made cabinets are cheaper on day one. Custom cabinets are usually cheaper over 5-10 years. The first invoice differs mainly by carcass board, door finish and hardware brand. The 5-10 year bill differs by moisture damage, hinge and runner replacement, and re-fitting cabinets that never matched the room. Compare both on the same written specification.

Which is cheaper up front: custom or ready-made cabinets?

Ready-made is cheaper up front. A stocked cabinet is built to one size, one finish and one hardware grade, in volume, and it is already in a warehouse. A custom cabinet is built from your drawings, so you pay for the drawing, the non-standard size and the finish you chose.

The size of that gap is not fixed. In our quoting experience the three biggest price swings are, in order: door finish, countertop, hardware brand. Carcass board matters too, but the carcass is largely hidden. The door is what you touch every day, and the finish process is where labour sits. A PVC membrane door and a high-gloss lacquer door can be the same panel underneath and still sit in different price tiers.

That is why a per-square-metre or per-linear-metre comparison between a ready-made set and a custom set is usually meaningless. The same 6-linear-metre run in E1 melamine-faced particleboard with PVC membrane doors and DTC hinges is a different product from the same 6 metres in an E0 plywood carcass with matte lacquer doors, Blum hinges and a sintered stone top. Both are "6 metres of kitchen". They are not the same purchase.

What does the 5-10 year maintenance bill actually contain?

Four line items. They are the reason the cheap cabinet is not always the cheap decision.

  • Moisture damage to the carcass. Particleboard with melamine facing is the lower-cost board and performs within its specification. In a Philippine ground-floor kitchen, a coastal site, or under a sink that has leaked once, that specification is being tested. Swollen board cannot be repaired — the cabinet is replaced.
  • Hinge and runner replacement. Soft-close mechanisms are wear parts. A branded hinge and runner set is a line you can read in a quote; an unbranded one is a line you cannot. Replacing hardware across a full kitchen is a real cost, and doing it twice removes the saving.
  • Re-fitting. A ready-made cabinet that is 40 mm short of the wall gets a filler panel. A ready-made tall unit that does not clear the ceiling gets a gap that collects dust and grease. Neither is a repair bill, but both are visible for the life of the kitchen.
  • Replacement of the whole run. This is the item buyers underestimate. If the carcass fails at year 6, you are not repairing — you are buying a kitchen again, and paying for removal and disposal on top.

We do not publish a maintenance statistic, because we have not measured one across Philippine installations and will not invent it. The honest statement is structural: a plywood carcass is the specification to discuss for humid sites, coastal locations and ground-floor kitchens where moisture is a real condition rather than a theoretical one. A melamine-faced particleboard carcass is a different specification with a different service life.

Does plywood versus particleboard matter in Philippine humidity?

Yes, and it is the first question to settle, because it is a carcass-level decision you cannot change later without replacing the cabinet.

We offer three carcass options: E0/E1 plywood, particleboard with melamine facing, and solid wood. The choice is a specification decision, not a marketing one. Plywood holds up better where moisture is present. Melamine-faced particleboard is the lower-cost route and is appropriate where the cabinet is in a dry, well-ventilated position and the budget is fixed.

For a developer fitting out multiple units, the carcass decision is also the decision that sets your warranty exposure. A cheaper board lowers the unit cost and raises the number of callbacks you will handle in the first three years. That trade is worth writing down before you choose.

How do freight and duty change the comparison in the Philippines?

They change it a lot, and they are the part most comparisons leave out. A ready-made cabinet bought locally has already absorbed freight into its shelf price. A custom cabinet shipped from a factory carries freight, duty, port and customs charges, and installation — and those depend on the terms you buy on: FOB, CIF or DDP.

Shipping format matters as well. Flat-pack and assembled are both available, and flat-pack reduces the volume you pay freight on. But the decision is not automatically flat-pack. It depends on your installation crew in the Philippines. If assembly quality on site is uncertain, the freight saving can be spent twice fixing joints. For a single house, assembled is often the simpler buy. For a multi-unit project with a trained crew, flat-pack is where the freight saving is real.

This is why a landed-cost comparison, not a factory-price comparison, is the only one that answers the question. Ask every supplier for the same delivery term before you put two numbers side by side.

What is the minimum order for custom cabinets, and does it kill small projects?

No. MOQ starts at 1 set for sampling, and project pricing applies from 20 sets upward.

That structure matters for Philippine developers and contractors running multi-unit work. A single showroom unit can be produced at sample MOQ to approve the finish and the fit, then the tower or the subdivision is priced at project level. You are not asked to commit 20 sets to see whether the lacquer matches the sample.

For a single homeowner, the sample route is the honest one: buy one cabinet, look at it in your own light, then decide on the rest. It costs more per unit than a 20-set order, and it is still cheaper than replacing a full kitchen at year 6.

How long does a custom order take, and what does that cost you?

Custom cabinets are not a stock item, so the schedule is part of the cost. Production runs on drawings, and the clock starts when the drawings are approved, not when you enquire.

Free shop drawings are issued after deposit. That sequence is deliberate: the drawing is the document that fixes the specification, and the specification is what the price is built from. A quote issued before drawings is an estimate, and an estimate is what buyers argue with later.

If your project has a handover date, work backwards from it. A ready-made cabinet can be collected this week. A custom kitchen cannot, and a compressed schedule that forces a substitution mid-project is how a cheap cabinet ends up in an expensive kitchen.

What should I send to get a comparable custom quote?

Send these and the quote is a quote, not an estimate:

  • Floor plan with dimensions, and ceiling height at the kitchen.
  • Elevations of each cabinet run.
  • Door finish and colour direction.
  • Countertop material and edge detail.
  • Hardware brand and grade — Blum, Hettich or DTC, and whether soft-close is required.
  • Delivery term: FOB, CIF or DDP.
  • Flat-pack or assembled.
  • Installation: your crew, or supervision required.

With those eight items, two suppliers can be compared line by line. Without them, you are comparing a number to a number and calling it a decision.

So which is cheaper in the Philippines?

Ready-made is cheaper if the cabinet is going into a dry, standard-sized position, you are not staying long, and the hardware is branded. Custom is cheaper over 5-10 years if the room is non-standard, the site is humid or coastal, the carcass is E0/E1 plywood, and the hardware is specified by brand.

The comparison only works on a written specification. Put the carcass board, the door finish, the hinge and runner brand, the countertop and the delivery term on one page for both options. The cheaper column is then visible, and it is usually not the one with the lower first invoice.

Frequently asked questions

Are ready-made cabinets really cheaper than custom cabinets in the Philippines?

On the first invoice, yes. Ready-made is built in volume to one size and finish, so it carries no drawing cost and no non-standard sizing. Over 5-10 years the gap narrows or reverses, because a low-cost melamine-faced particleboard carcass in a humid or coastal site can fail and be replaced rather than repaired.

What are the biggest cost drivers in a custom cabinet quote?

In our quoting experience the three biggest swings are door finish, countertop and hardware brand, in that order. Carcass board matters but is largely hidden. The door is what you touch daily and the finish process is where labour sits, so a PVC membrane door and a high-gloss lacquer door can be the same panel underneath.

Does plywood versus particleboard matter in Philippine humidity?

Yes, and it is the first decision to settle because you cannot change the carcass later without replacing the cabinet. We offer E0/E1 plywood, particleboard with melamine facing, and solid wood. Plywood is the specification to discuss for humid sites, coastal locations and ground-floor kitchens where moisture is a real condition.

What is the minimum order for custom cabinets from your factory?

MOQ starts at 1 set for sampling, and project pricing applies from 20 sets upward. That lets a Philippine developer produce a single showroom unit to approve the finish, then price the tower or subdivision at project level without committing 20 sets before seeing a sample.

Should I ship custom cabinets flat-pack or assembled to the Philippines?

It depends on your installation crew. Flat-pack reduces the freight volume you pay for, but if assembly quality on site is uncertain the freight saving can be spent twice fixing joints. For a single house, assembled is often simpler. For a multi-unit project with a trained crew, flat-pack is where the saving is real.

How do I compare a ready-made price with a custom quote fairly?

Put the same eight items on one page for both: floor plan and ceiling height, elevations, door finish, countertop material and edge, hardware brand and grade, delivery term (FOB, CIF or DDP), flat-pack or assembled, and who installs. Without those, you are comparing a number to a number, not a specification to a specification.