How to read a drawing set we send back
A millwork package for an apartment is 40 to 120 pages. Most of what goes wrong on site is traceable to five of them. Here is which five.

How to read a drawing set we send back
A millwork package for an apartment is 40 to 120 pages. Most of what goes wrong on site is traceable to five of them. Here is which five.
We send back a package you did not ask for: elevations, sections, a hardware schedule and a panel legend. It is long because on a project of forty units a single unresolved dimension repeats forty times.
Read these five sheets first — the plan with unit numbers, the elevation set for one representative room, the section through the wall where cabinetry meets the slab, the hardware schedule, and the panel and finish legend. If those five agree with each other, the other hundred pages are detail.
The place a project fails is not the cabinet face. It is the interface: cabinet to wall, cabinet to floor, cabinet to the door frame that is already installed. Those are the sheets to sign, not the pretty elevation.
How do you trace a dimension from plan to section to elevation?
Pick one unit number from the plan and follow it through the set. The plan gives the room outline and the unit number; the elevation for that room gives the cabinet face layout; the section gives the depth relationship between the cabinet back, the wall and the slab. If the same dimension appears on all three sheets with the same value, that part of the set is internally consistent. If a dimension appears on the elevation but not on the section, the interface is unresolved.
Do this for one representative room before reading anything else. The exercise shows you where the set is complete and where it relies on a note rather than a drawn dimension. A note that says the filler is field-verified is not the same as a drawn dimension, and the difference matters at the wall where the cabinetry meets the slab.
Keep a short list of every dimension you could not trace to a second sheet. That list, not the full package, is what you send back with your comments.
What should you compare between the drawing set and the site?
The set describes the interface, so compare it against what is actually built. Check the door frame that is already installed against the elevation that shows cabinetry meeting it. Check the slab line in the section against the floor you can see. Check the wall the cabinets run against for the same conditions the section assumes.
Where the site and the drawing disagree, the drawing is the question and the site is the answer. Mark the disagreement on the sheet rather than resolving it in conversation, so the correction lands in the next issue of the set and not only in someone's memory.
Compare the hardware schedule against the elevation at the same time. A hinge or slide listed in the schedule should correspond to a door or drawer shown on the elevation. A schedule line with no matching elevation callout is a gap worth raising before anything is released.
What are the common mistakes buyers make when reviewing a returned set?
The first mistake is reading the elevations and skipping the sections. The elevation shows the face; the section shows the interface, and the interface is where the project fails. The second is treating the hardware schedule and the panel legend as paperwork rather than as part of the drawing. If the legend and the elevation disagree on a finish, the set is not ready to sign.
The third mistake is reviewing one sheet at a time instead of checking that the five key sheets agree with each other. Agreement across sheets is the test; a single sheet can look correct and still conflict with the section through the wall.
The fourth is signing the pretty elevation because it looks finished. Sign the interface sheets instead. The fifth is sending comments verbally. Put them on the sheet, tied to the unit number and the dimension, so the next issue can be checked against them.
Start with
a brief.
Send the drawings and the room list. We will come back with a scope, a finish schedule and a price range.
Buyer questions
Which sheets in a millwork drawing package should we review first?
Read five sheets first: the plan with unit numbers, the elevation set for one representative room, the section through the wall where cabinetry meets the slab, the hardware schedule, and the panel and finish legend. If those five agree with each other, the remaining pages are detail. A package for an apartment runs 40 to 120 pages.
Where do millwork problems usually occur on site?
Problems are not in the cabinet face. They occur at the interface: cabinet to wall, cabinet to floor, and cabinet to the door frame that is already installed. Those interface sheets are the ones to sign, not the pretty elevation. On a forty-unit project, a single unresolved dimension repeats forty times.
What does the drawing package include and why is it so long?
The package includes elevations, sections, a hardware schedule and a panel legend. It is long because on a project of forty units a single unresolved dimension repeats forty times. The package is sent back even though you did not ask for it, so the five key sheets can be checked for agreement before the rest is treated as detail.