Home / Journal
COMPANY NOTES

Green board and the E0 line: what changed in the panel

The 2014 green-panel programme and the numbers a buyer should actually ask for.

经典厨房定制
GREEN BOARD· 2014

Green board and the E0 line: what changed in the panel

The 2014 green-panel programme and the numbers a buyer should actually ask for.

In 2014 the brand launched the 'Green Value Era' forum together with an E0-grade green board and a long-running environmental programme. The panel is the part of a millwork quote that is easiest to under-specify, because it is invisible once the doors are on.

What we quote is: panel grade and emission class in writing, edge banding method, and a formaldehyde test report with a batch date. A current cabinet-panel report we hold, tested to GB/T 39600-2021, shows 0.012 mg/m³ against an ENF limit of 0.025 — see the company facts page for the full table and the batch note.

The rule for buyers: never accept 'E0 grade' as an adjective on a quotation. Ask for the grade standard number, the test report number and the batch date. If any of the three is missing, the grade is not a specification, it is a slogan.

How do you verify a panel's emission grade during production?

Verification starts before the panel is cut. Ask the supplier to identify the panel grade and emission class in writing on the production order, not just on the quotation. The written record should reference the grade standard number and the test report number, and it should carry a batch date that matches the panel batch used for your order. During production, request that the edge banding method be documented as part of the work order, because the edge treatment affects how the panel performs in the finished cabinet.

At the factory, check that the panel batch date on the incoming material matches the batch date on the test report. If the supplier cannot show a report with a batch date that corresponds to the material in use, the grade claim is not tied to the actual panel. Also confirm that the formaldehyde test report is current and that it was tested to the standard cited in the quotation. The report should show the measured value and the limit it is compared against, so you can see the margin rather than accept a label. Keep a copy of the report and the batch note with your project records so the specification can be traced after the cabinets are installed.

What should a buyer compare when reviewing panel specifications from different suppliers?

Compare the written specification, not the marketing description. For each supplier, look for the panel grade and emission class stated in writing, the grade standard number, the test report number, and the batch date. A quotation that says only 'E0 grade' without these three items does not give you a comparable specification. Put the responses side by side and check whether each supplier provides all three, or whether some leave one out.

Next, compare the edge banding method. The method should be described in the quotation or work order, because it is part of how the panel is finished and affects the cabinet's performance. Then compare the formaldehyde test report: confirm the standard it was tested to, the measured value, and the limit used for comparison. A report that shows a measured value against a stated limit gives you a basis for comparison; a report that only states a grade does not. Finally, check the batch date on the report against the batch date of the panel supplied. If the dates do not correspond, the report may not represent the material you are buying. Use these points as a checklist when reviewing each supplier's documentation.

What common mistakes lead buyers to accept an unverified panel grade?

The most common mistake is treating 'E0 grade' as a specification when it is used as an adjective on a quotation. Without the grade standard number, the test report number, and the batch date, the term does not tell you what panel you are buying. Buyers often accept the phrase because it sounds technical, but it does not tie the claim to a test or a batch.

Another mistake is reviewing the test report without checking the batch date against the panel batch. A report can be genuine but relate to a different production batch, so the batch date is what connects the report to your order. Buyers also sometimes overlook the edge banding method, even though it is part of the panel specification and should be stated in writing. A further mistake is comparing suppliers on the grade label alone rather than on the full set of written items: grade and emission class, standard number, report number, batch date, and edge banding method. When one of these is missing, the comparison is not like for like. The rule is simple: if any of the three key items — grade standard number, test report number, batch date — is missing, the grade is not a specification, it is a slogan.

ENQUIRY

Start with
a brief.

Send the drawings and the room list. We will come back with a scope, a finish schedule and a price range.

Your details stay with our project team. No mailing lists.

Buyer questions

What should I ask for to verify the E0 board grade on a millwork quote?

Ask for three things: the grade standard number, the test report number and the batch date. The article states that if any of the three is missing, the grade is not a specification, it is a slogan. Never accept 'E0 grade' as an adjective on a quotation. What we quote is panel grade and emission class in writing, edge banding method, and a formaldehyde test report with a batch date.

What formaldehyde emission test result does your cabinet panel report show?

A current cabinet-panel report held by the company, tested to GB/T 39600-2021, shows 0.012 mg/m³ against an ENF limit of 0.025. The full table and batch note are on the company facts page. Buyers should still request the grade standard number, test report number and batch date for their own order rather than relying on a general claim.

What changed in the panel with the 2014 green board programme?

In 2014 the brand launched the 'Green Value Era' forum together with an E0-grade green board and a long-running environmental programme. The panel is the part of a millwork quote easiest to under-specify because it is invisible once the doors are on, so the company quotes panel grade and emission class in writing, edge banding method, and a formaldehyde test report with a batch date.