Shadow Gap Doors: Cost, Tolerance and Site Finishing Explained
Shadow gap doors are quoted from approved shop drawings, not a price list, and production runs 25-35 days after drawing approval and deposit. The gap is a site-tolerance decision as much as a design one: it must be set at drawing stage, because a reveal cut wrong cannot be widened on site.
Shadow gap doors are quoted from approved shop drawings, not a catalogue price. The number is built from door core, finish, hardware and the reveal or jamb lining that meets the wall. Production runs 25-35 days after drawing approval and deposit, MOQ from 1 set for sampling, and project pricing from 20 sets.
What actually drives the cost of a shadow gap door?
Five blocks, and the reveal is only one of them. Buyers usually assume the shadow gap is the expensive part. In practice the gap is a machining and setting-out cost; the money sits in the door core, the finish, the hardware and the wall panels that meet the door.
- Door core and carcass board — the substrate choice moves the price more than the reveal detail does.
- Door and panel finish — lacquer, PET, acrylic, veneer or PVC membrane. Lacquer in matte or gloss is the most specification-sensitive.
- Hardware — Blum, Hettich or DTC, and you can specify which. Concealed hinges and a flush pull cost differently from a standard lever.
- Wall panelling and trims — the panels, reveals and skirting that close the junctions around the door.
- Freight, duty and installation — the block buyers most often forget when comparing a factory quote to a local joinery quote.
The reason the gap itself is cheap to produce and expensive to get wrong: it is cut on the same panel system as the cabinetry, so consistency comes from the setup, not from hand-fitting on site.
How tight is the tolerance on a shadow gap, and who owns it?
The gap is a shared tolerance between the door unit and the wall opening. The factory controls the door leaf, the frame or jamb lining, and the reveal profile. It does not control the plastered or drylined opening it lands in. That split is where most shadow gap failures originate.
Two consequences follow. First, the gap dimension must be agreed at drawing stage, not at installation — a reveal cut for one gap cannot be widened on site, and a unit that arrives short of the wall gets a filler panel, which is visible for the life of the room. Second, the acceptance standard has to be written down before production starts. A flat sample will not show you a shadow gap problem; a finished corner will.
What to demand in writing before production
- The nominal gap dimension, stated once, and the permitted deviation either side of it.
- Which party is responsible for the opening — who surveys it, and what happens if it is out.
- The junction detail at floor, ceiling and adjacent wall panels, drawn, not described.
- The inspection method: which corners are checked, at what light, by whom.
Why order doors and wall panels from the same factory?
Because the gap only reads as a gap if every surface meeting it is made on the same setup. If you order doors from one supplier and wall panels from another, the reveals will not line up — the two factories are working to different setting-out assumptions, and neither is wrong, they are just different.
Buying the door and wall system as one package is what keeps the shadow gaps consistent. The package in practice contains door leaves, door frames or jamb linings, architraves or a shadow-gap reveal, wall panels (flat, slatted or grooved), skirting, and the trims that close the junctions. Because these parts are cut, edged and finished on the same line as cabinetry, the specification logic carries over directly from kitchen cabinetry — and so do the cost drivers.
How should I compare shadow gap options on cost?
Compare like for like across the whole junction, not the door leaf alone. The table below sets out the decision levels a buyer actually chooses between. It is a comparison framework, not a price list — your quote comes from approved shop drawings.
| Option | What it changes | Cost effect | Site risk |
|---|---|---|---|
| Standard architrave | Covers the wall/ frame junction | Lowest trim cost | Low — forgiving of opening deviation |
| Shadow gap reveal, doors only | Gap at door perimeter only | Moderate | Medium — gap must match adjacent panels |
| Shadow gap reveal, full door and wall package | Gap continuous across door and panelling | Highest, but one supplier and one setup | Lowest — single tolerance owner |
| Mixed suppliers (doors A, panels B) | Two setting-out assumptions | Appears cheaper per line | Highest — reveals will not line up |
Read the table by the last column. The cheapest line item is frequently the most expensive outcome, because rework on site is charged at site rates, not factory rates.
What are the lead time and MOQ realities?
Production runs 25-35 days after drawing approval and deposit. That clock starts at drawing approval, not at enquiry — which is why the gap dimension and the junction details have to be settled early. Every week spent deciding the reveal is a week added to delivery.
MOQ starts at 1 set for sampling, and project pricing applies from 20 sets. For a developer, the sampling set is not a formality: it is the only chance to see a finished corner and agree the acceptance standard before the production run commits.
What goes wrong on site, and how do I prevent it?
Most shadow gap defects are predictable, and most are caught by inspecting a finished corner rather than a flat sample.
- Inconsistent shadow gaps where reveals were machined on different setups.
- Colour or sheen mismatch between edge band and face — invisible in the sample room, obvious in daylight on site.
- Chipped or rounded corners where a band was trimmed after application.
- Edge damage in transit, which is a packing problem as much as a production problem.
- Filler panels at the wall junction, visible for the life of the room.
Prevention is contractual, not cosmetic: fix the gap at drawing stage, name one tolerance owner, agree the acceptance standard in writing, and inspect a finished corner before the run starts.
Frequently asked questions
How much does a shadow gap door cost?
There is no catalogue price. A shadow gap door is quoted from approved shop drawings, built from five blocks: door core and carcass board, door and panel finish, hardware brand, wall panelling and trims, and freight, duty and installation. The reveal detail itself is a small part of the number — the finish and hardware move the price more.
What is the lead time for shadow gap doors from a Chinese factory?
Production runs 25-35 days after drawing approval and deposit. The clock starts at drawing approval, not at enquiry, so every week spent deciding the gap dimension and junction details adds a week to delivery. Settle the reveal before you release the drawings.
What is the minimum order quantity?
MOQ starts at 1 set for sampling, and project pricing applies from 20 sets. For a developer the sampling set matters — it is the only chance to inspect a finished corner and agree the acceptance standard before the production run commits.
Can I widen a shadow gap on site if it looks wrong?
No. A reveal cut for one gap cannot be widened on site, and a unit that arrives short of the wall gets a filler panel that stays visible for the life of the room. The gap must be decided at drawing stage, which is why it belongs in the shop drawing review, not the installation conversation.
Who is responsible for the tolerance — the factory or the site?
It is shared. The factory controls the door leaf, frame or jamb lining and reveal profile. It does not control the plastered or drylined opening the unit lands in. Name one party responsible for surveying the opening, and state in writing what happens if it is out of tolerance.
Should I buy doors and wall panels from the same supplier?
Yes, if the shadow gap runs across both. Two suppliers means two setting-out assumptions, and the reveals will not line up — neither is wrong, they are just different. Buying the door and wall system as one package is what keeps the gaps consistent.
What should I inspect before approving production?
A finished corner, not a flat sample. Check the gap consistency, the colour and sheen match between edge band and face in daylight, and the corner where the band was trimmed. Agree the acceptance standard in writing before the run starts.
What finish options exist for shadow gap doors?
Door finish is lacquer in matte or gloss, PET, acrylic, veneer or PVC membrane. Carcass board is E0 or E1 plywood, particleboard with melamine, or solid wood. Hardware is Blum, Hettich or DTC, and you can specify which. The finish choice is one of the largest cost drivers in the quote.