TV Wall Joinery: Cable Routes, Access Panels and Storage
TV wall joinery is quoted from approved shop drawings, not a catalogue, and the cable route, access panel and storage layout must be fixed at drawing stage because they cannot be cut in later. Production runs 25–35 days after drawing approval and deposit, with MOQ from 1 set for sampling.
TV wall joinery is a factory-built wall unit quoted from approved shop drawings, not a catalogue. The cable route, access panel and storage layout must be fixed at drawing stage, because a route cut wrong on site cannot be widened behind a finished panel. Production runs 25–35 days after drawing approval and deposit, with MOQ from 1 set for sampling.
What is TV wall joinery and what does it actually include?
TV wall joinery is the fixed millwork assembly that surrounds and supports a television: the back panel or cladding, the carcass that carries storage, the shelf and niche structure, and the concealed voids that carry power, data and AV cabling. It is a joinery package, not a piece of furniture.
In a project specification it usually breaks into five blocks, and each is priced separately:
- Wall cladding or back panel — veneer, lacquer, melamine or sintered stone face on a board substrate.
- Carcass and storage — base cabinets, drawer banks, open shelving, closed cupboards.
- Niche and reveal structure — the recessed boxes that hold the screen, a soundbar or display objects.
- Service voids and access — the cavity behind the cladding, the conduit route, the removable panel.
- Hardware and finish — hinges, runners, handles, edge treatment.
Because the wall is fixed to the building, the substrate matters as much as the joinery. A drywall wall, an MDF-lined wall and a masonry wall each take a different fixing method, and the tolerance you can hold depends on which one you have. That decision belongs in the drawing set, not on site.
How do you plan cable routes in TV wall joinery?
Plan the cable route before the panel layout, not after. The route is a void: a horizontal chase behind the cladding at screen height, a vertical drop to the floor or to a floor-level outlet, and a pull point where a cable can be pushed through without dismantling the wall.
Four things decide whether the route works:
- Where the power and data outlets actually are. Get the electrical drawing before you draw the joinery. If the outlet sits behind a fixed panel with no access, the wall is wrong.
- How many cables and how thick. A screen with power, two HDMI, one optical and one network cable needs a wider void than a screen with power alone. Ask the AV contractor for the cable schedule in writing.
- Bend radius. Optical and HDMI cables have a minimum bend radius. A route that turns sharply behind a panel will damage the cable or fail to pull.
- Future change. A route sized for today's cables will be too small in five years. Specify a spare draw cord or a spare conduit.
The practical rule: the cable void is designed as a continuous path from the screen position to the outlet, with no section narrower than the widest connector that must pass through it. Connectors, not cables, set the minimum size.
Where should access panels go in TV wall joinery?
Access panels go wherever a service connection, a junction box or a fixing point sits behind a closed surface. The minimum set is: one at the screen mounting position, one at the outlet or junction point, and one at any concealed hardware that may need adjustment.
Access panels are the part buyers most often delete to save cost, and the part they most regret deleting. A wall with no access panel means any future change — a new device, a failed socket, a loose fixing — requires cutting the finished face.
Three placement rules that hold up on site:
- Put the panel where a person can reach it without moving a sofa or standing on a ladder in an awkward position.
- Align the panel joint with a design line — a shadow gap, a shelf edge, a door reveal — so it reads as part of the composition rather than a patch.
- Size the opening to the hand and the tool, not to the cable. A panel that opens but gives no working room is not access.
On a project wall, mark every access panel on the drawing with its opening size and its fixing method, and confirm the panel is removable without disturbing adjacent panels. If the panel is held by the same clips as the fixed cladding, it is not an access panel.
How much storage should a TV wall include, and at what depth?
Storage depth is set by what goes in it, and the TV wall usually carries three different storage types with three different depths. Decide the contents first, then the depth, then the carcass.
| Storage type | Typical contents | What sets the depth | Cost driver |
|---|---|---|---|
| Closed base cupboard | AV equipment, boxes, files | Deepest item stored plus door clearance | Carcass board area, door finish, runners |
| Drawer bank | Remotes, cables, small items | Runner length and drawer box height | Runner grade, drawer box, front finish |
| Open shelving / niche | Display, books, soundbar | Shelf span and load, not contents | Shelf thickness, substrate, edge finish |
| Concealed service void | Cables, junction boxes | Connector size and bend radius | Extra carcass depth, access panel |
Two cost facts follow from this table. First, a service void adds depth to the whole wall, and depth is carcass board — so the void is paid for across the full run, not just at the screen. Second, open shelving is usually cheaper per square metre than a closed cupboard because it has no door, no runner and no handle, but it demands a stiffer shelf and a better edge finish.
Ventilation belongs in the same conversation. AV equipment and routers generate heat, and a closed cupboard with no ventilation path will cook them. Specify a vent route — a gap at the back of the carcass, a perforated panel, a louvred door — and put it on the drawing.
What should be on the shop drawing before you approve it?
Approve the drawing only when it shows the cable route, the access panels, the storage depths and the fixing method. A drawing that shows only the elevation is not a manufacturing drawing.
Checklist for the drawing review:
- Plan view showing the void depth behind the cladding and where it runs.
- Every access panel located, sized and given a fixing method.
- Outlet and junction positions marked, cross-checked against the electrical drawing.
- Storage depths stated per unit, with the contents assumption written down.
- Ventilation path shown for any closed AV compartment.
- Wall substrate and fixing method stated, with who owns the tolerance.
- Screen model and mounting bracket specified, because the bracket sets the fixing and the void.
Production runs 25–35 days after drawing approval and deposit. That clock starts at approval, so every drawing revision is a schedule cost, not just a design cost. MOQ is from 1 set for sampling and 20+ sets for project pricing, and shipping can be flat-pack or assembled, FOB, CIF or DDP. On a whole-house order the TV wall is usually one line among wardrobes, vanities and doors, so the drawing review is the point where the wall either fits the rest of the package or delays it.
What goes wrong most often on TV wall joinery?
The failures are predictable and almost all of them are drawing-stage failures.
- No access to the outlet. The cladding is finished over a socket that will eventually need attention.
- Cable void too small. Sized to the cable, not the connector, so nothing can be pulled through after handover.
- Heat build-up in a closed cupboard. No vent path, and the equipment fails within a year.
- Storage depth guessed. The cupboard is 20 mm too shallow for the item it was built for.
- Substrate tolerance not owned. The joinery is made to a tolerance the wall cannot hold, and the shadow gap opens up.
Each of these is fixed on paper at no cost, and fixed on site at the cost of a panel. That is the whole argument for treating the TV wall as a drawing exercise first and a joinery order second.
Frequently asked questions
How long does TV wall joinery take to manufacture and ship?
Production runs 25–35 days after drawing approval and deposit. The clock starts at approval, not at order, so drawing revisions push the date. Add sea freight transit on top of that, which varies by destination port. MOQ is from 1 set for sampling and 20+ sets for project pricing.
Do I need an access panel behind a wall-mounted TV?
Yes, at the screen mounting position and at the outlet or junction point. Without one, any future change — a new device, a failed socket, a loose fixing — means cutting the finished face. Mark each panel on the drawing with its opening size and fixing method, and confirm it can be removed without disturbing adjacent panels.
How wide should the cable void be in a TV wall?
Size it to the widest connector that must pass through, not to the cable. Ask the AV contractor for the cable schedule in writing, including how many cables and their types. Optical and HDMI cables have a minimum bend radius, so a route with sharp turns behind a panel will damage the cable or fail to pull.
How deep should TV wall storage be?
Depth is set by contents, so decide contents first. Closed base cupboards are set by the deepest item plus door clearance; drawer banks by runner length; open shelving by shelf span and load rather than contents. A concealed service void is set by connector size and bend radius, and it adds depth across the full wall run.
Is open shelving cheaper than closed cupboards on a TV wall?
Usually yes per square metre, because open shelving has no door, no runner and no handle. But it demands a stiffer shelf and a better edge finish, and it offers no place to hide AV equipment. The cheaper option depends on what the wall has to store, not on the unit price alone.
How do I stop AV equipment overheating inside a closed TV wall cupboard?
Specify a ventilation path and put it on the drawing: a gap at the back of the carcass, a perforated panel or a louvred door. AV equipment and routers generate heat, and a closed cupboard with no vent route will cause failures. This is a drawing-stage decision, not something to solve after installation.
What is the minimum order for custom TV wall joinery from a China factory?
MOQ is from 1 set for sampling, and 20+ sets for project pricing. Sampling at 1 set lets you check the cable route, access panel and finish before committing to a project quantity. Shipping can be flat-pack or assembled, and terms can be FOB, CIF or DDP.
What should be on the shop drawing before I approve a TV wall?
A plan view showing void depth and route, every access panel located and sized with a fixing method, outlet positions cross-checked against the electrical drawing, storage depths stated per unit, the ventilation path for closed AV compartments, the wall substrate and fixing method, and the screen model and bracket.